"The opinions posted here do not represent those of any company, organization, or group and are those only of the author of the respective post." - From Rontini |
May - June 2018 Dolphin Brotherhood Posted |
Post Reply |
Author | |
Dave S.
Old Salt Joined: 04 Jan 2016 Location: Seattle Status: Offline Points: 228 |
Post Options
Thanks(0)
Posted: 30 Apr 2018 at 11:03pm |
Shipmates,
The May - June 2018 issue of the Seattle USSVI Base newsletter has been posted and is ready to view and download. This issue has Base updates, news about the decommissioning of a couple submarines, along with other submarine related articles from around the world. Hardcopies will be mailed out later this week. I hope you all enjoy the newsletter. As always, remember to check Seattle Base Blog for base updates and other articles of interest. Dave Schueler Seattle Base Newsletter Editor |
|
610ET
Rickover Joined: 04 Jan 2016 Location: Fort Lauderdale Status: Offline Points: 2186 |
Post Options
Thanks(0)
|
Interesting article on the Aluminaut. In the article it states that she could dive much deeper than other submarines because she could stand ocean pressure of up to 7,500 psi. Most of our boats were built of HY 80 steel which could take up to 80,000 psi but we couldn't dive anywhere near the Aluminaut's wiki stated test depth of 17,000 feet. To this non-engineer it doesn't seem to add up. What am I missing? Edited by 610ET - 02 May 2018 at 3:41pm |
|
SaltiDawg
Rickover Joined: 03 Jan 2016 Location: Rockville, MD Status: Offline Points: 2865 |
Post Options
Thanks(0)
|
I'm apparently not up to understanding what a grounding is in Navy Parlance , so I won't answer this.
Edited by SaltiDawg - 02 May 2018 at 7:00pm |
|
610ET
Rickover Joined: 04 Jan 2016 Location: Fort Lauderdale Status: Offline Points: 2186 |
Post Options
Thanks(0)
|
How old are you, 12? Good grief. |
|
SaltiDawg
Rickover Joined: 03 Jan 2016 Location: Rockville, MD Status: Offline Points: 2865 |
Post Options
Thanks(0)
|
I'm the one that said, " With a "grounding" of virtually any sort, pretty understandable if NAV,
CO, and Quartergasket(s), not to mention OOD have some blame.
"Some blame" means career ending, at least. I'm not familiar with this grounding other than brief reference in this book - by an author that had not earned any respect as shown by his admissions." To which you replied, "Be interesting to see how the Navy classified it. He certainly wasn't appreciative of learning about a serious submarine event that he somehow had missed. Maybe he just likes to be "right?" Next, a couple of posters each cited the investigation as referring to the GROUNDING, just as I had referred to the GROUNDING in discussing what typically happens to the CO, OOD, Nav, QMs, etc. GROUNDING is the correct term, notwithstanding what a person with a couple of years in might prefer. I'm the 12 year old that understands the answer to your question. Edited by SaltiDawg - 02 May 2018 at 8:09pm |
|
610ET
Rickover Joined: 04 Jan 2016 Location: Fort Lauderdale Status: Offline Points: 2186 |
Post Options
Thanks(0)
|
As I said, good grief.
In that other thread which has nothing to do with this one you early on stated that you weren't familiar with the San Fran accident. I then posted a link to what happened so that you would learn and you responded, not with a thank you but a bizarre response of "er, OK". Also, I didn't say that it wasn't a grounding. I said that it wasn't your average grounding and wondered how it was classified by the navy. Others then called you out and you deleted your posts and said never mind. I have no idea why you keep responding to me negativly but here is a thought, just ignore what I write if I bother you that much. Also, why respond if you don't know the answer to the question? Edited by 610ET - 03 May 2018 at 12:44am |
|
oldsubs
Neptune Joined: 15 Jan 2016 Location: St Augustine FL Status: Offline Points: 2070 |
Post Options
Thanks(0)
|
The yield strength of the material is the amount of force needed to just deform the material to the point that the deformation is permanent. The test is normally one of tensile strength or 'pull'. A sample of the material is placed in a machine, fastened at both ends then pulled apart. At some point, the material, if the force is removed, will not 'spring back' to its original size. This is then the yield strength. A further pull will deform the material up to its failure point.
The above is a simplified explanation. The important points are that the test is a tensile strength test. When we think of our pressure hulls, the sea pressure will generally put a compression on the hull steel not a tension (they are in opposite directions). This too is a simplified explanation. The depth to which we might safely submerge is based on many things other than the 'raw' strength number of the hull material. Other considerations are, but not limited to, packing gland holding pressure for sea systems, sea water piping, hull opening strength, hull geometry, speed/depth operating envelope limits, etc. The Aluminaut was not made to operate like a modern US submarine thus had less limits to its possible operating depths than we do (did). The Aluminaut's operating depth has no relation to our operating depths. The "HY-" number is a general descriptor for an alloy of steel. It does not have a direct relation to our operating depths but does have a general relationship to the raw strength of the hull steel. You are not missing anything that a couple of engineering courses wouldn't cure. |
|
Be Well
Oldsubs |
|
FTGC(SS) Lane
Old Salt Joined: 05 Jan 2016 Location: Conway New Hamp Status: Offline Points: 262 |
Post Options
Thanks(0)
|
Um, no he didn't. |
|
610ET
Rickover Joined: 04 Jan 2016 Location: Fort Lauderdale Status: Offline Points: 2186 |
Post Options
Thanks(0)
|
Thank you but that ship has sailed. Edited by 610ET - 03 May 2018 at 11:02am |
|
SaltiDawg
Rickover Joined: 03 Jan 2016 Location: Rockville, MD Status: Offline Points: 2865 |
Post Options
Thanks(0)
|
I know! I even apologized and posted, "Never mind. Sorry." Edited by SaltiDawg - 05 May 2018 at 5:31pm |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |